New City Trenchless locates sewer and underground water line leaks before anyone opens the ground. A hidden leak under a slab, a driveway or a lawn does not announce where it is, and digging to find it turns a buried pipe into a buried trench. Leak detection is the diagnostic step that replaces guesswork with a marked spot, so the repair that follows is cut to the length of pipe that actually failed.
This page is about finding the leak. Visual grading of a sewer lateral is handled on the camera inspection page, and the fixes are covered on the repair pages linked below. Here the job is one thing: pinpoint the leak on the sewer lateral or the water service line so the repair is planned, not improvised.
Signs You Have a Hidden Sewer or Water Line Leak
A buried leak usually shows itself at the surface or on a bill long before anyone sees the pipe. Catching the signs early is what keeps a located repair from becoming an emergency excavation.
Wet Spots, Meter Spin, and Unexplained Bills
A pressurized water service line that is leaking loses water continuously, so the first sign is often the water bill climbing with no change in how the household uses water. A water meter that keeps turning with every fixture in the house shut off points the same direction. Above the line itself, a patch of lawn that stays green and soft through a dry stretch, or a damp area on a basement slab or wall, marks where the water is surfacing. None of these says exactly where the leak is, only that there is one, which is where locating and testing take over.
Smell, Settling and Soft Ground Over the Lateral
A sewer lateral leaks differently. Because it runs by gravity rather than pressure, the tell is what collects around it: a sewer odor near the cleanout or in the yard, ground that stays wet or spongy along the pipe path, or a strip of soil that has settled where soil is washing into a cracked joint. Over time that loss of bedding shows up as a dip in the lawn or a crack in a slab or driveway above the run. These signs locate the general area; a camera and a locator turn the general area into a marked point.
How We Find the Leak Before We Dig
The point of leak detection is to spend the effort above ground so the digging, if any, is small and in the right place. The method depends on which line is suspect, and sorting that out comes first.
Line Locating and Sonde Tracing
Before anything else we establish where the pipe actually runs and how deep it sits. A line locator picks up the signal from a traceable line or from a sonde pushed through the pipe, and the path gets marked on the surface along with the depth at the leak area. That map matters twice: it keeps the diagnosis focused on the real run instead of where a pipe is assumed to be, and it keeps any later excavation off other utilities. Tracing the line is also how a long run under a driveway or a mature tree gets diagnosed without disturbing what is on top of it.
Pressure Testing and Camera Confirmation
With the line located, the test is matched to the system. A pressurized water service line is isolated and pressure tested, so a section that will not hold pressure confirms the leak is there and roughly how far along the run. A gravity sewer lateral is confirmed by a camera inspection, which puts a lens on the cracked joint, offset or hole and records the footage to it. Used together, locating plus the right test turns wet ground into a marked spot with a depth and a distance, which is everything the repair needs.
From Found Leak to Repair Option
Finding the leak is the point where the right fix becomes a short list instead of a guess. Because the defect is now located to a length of pipe and a depth, the repair is scoped to that, not to the whole yard.
A single failed joint or a short defect on an otherwise sound sewer lateral often suits a sectional spot repair, which seals one bad section without touching the rest of the line. A leak on a buried water service line routes to water line replacement, which can often be pulled through trenchlessly once the run is located. A sewer lateral that is leaking in more than one place, or losing grade, moves into sewer line repair and replacement. In every case the located leak is what keeps the repair planned and proportionate, a small access window over a known defect rather than an exploratory trench.
The mains in Rockland County are the sewer district’s responsibility, but the lateral from the house to the tap, and the water service line into the house, belong to the homeowner. That is exactly the stretch where a hidden leak hides, and exactly the stretch leak detection is built to pinpoint before the first shovel goes in.
Frequently Asked Questions
How do you find a buried leak without digging up the whole yard?
We start above ground. A line locator and sonde trace the exact path and depth of the pipe, then a pressure test on the water service or a camera pass on the sewer narrows the leak to a short section. Only then does anyone break ground, and the dig is a small window over the located defect rather than an exploratory trench across the lawn.
Can you tell the difference between a sewer leak and a water line leak?
Yes. The two run on different systems and get tested different ways. A pressurized water service line holds and loses pressure, so a pressure test confirms it and a locator traces the run. A gravity sewer lateral is diagnosed by camera and by what is showing at the surface, wet ground, odor or settling. Sorting which line is leaking is the first question we answer, because it decides the repair.
What happens after you locate the leak, do you repair it the same visit?
Sometimes, depending on access, depth and what the diagnosis finds. Leak detection is the step that defines the repair, not the repair itself. Once the leak is pinpointed we scope the fix, a spot repair, a lined or replaced section, or a replaced water service, and schedule it. Locating first means the repair is planned to the right length of pipe instead of discovered mid dig.
